NETGEAR ReadyNAS Duo v2
HDD が見えたときの dmesg、panic してるけどな :-P
mvgbec1 が attach された時点でフリーズするのでコンフィグで無効化してる。
もしかして mvpex* は要らないのかなー。PCI Express で何かが接続されている訳でも無さそうだし。
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Jun 29 2012 - 16:06:40) Marvell version: 3.4.27
Netgear version: Uboot-1_1_4-NetgearDUOV3-V1009
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0120
Soc: MV88F1155 Rev 1 (DDR3)
CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM unknown CAL tRP = 8 tRAS = 20 tRCD=8
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Switch On !
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> tftpboot
*** Warning: no boot file name; using 'C0A800DC.img'
Using egiga0 device
TFTP from server 192.168.0.2; our IP address is 192.168.0.220
Filename 'C0A800DC.img'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###################################
done
Bytes transferred = 5168512 (4edd80 hex)
Marvell>> bootm 0x2000000
## Booting image at 02000000 ...
Image Name: NetBSD/readynasduov2 6.99.19
Created: 2013-04-09 14:00:38 UTC
Image Type: ARM NetBSD Kernel Image (uncompressed)
Data Size: 5168448 Bytes = 4.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Transferring control to NetBSD stage-2 loader (at address 00008000) ...
NetBSD/evbarm (readynasduov2) booting ...
[ Kernel symbol table missing! ]
Loaded initial symtab at 0xc0426854, strtab at 0xc0460774, # entries 14819
pmap_postinit: Allocated 35 static L1 descriptor tables
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.99.19 (READYNASDUOV2) #1: Tue Apr 9 23:00:38 JST 2013
nonaka@koharu.myhome.local:/home/nonaka/repo/NetBSD/src/sys/arch/evbarm/compile/obj.evbarm/READYNASDUOV2
total memory = 256 MB
avail memory = 245 MB
cprng kernel: WARNING insufficient entropy at creation.
mainbus0 (root)
cpu0 at mainbus0 core 0: Sheeva 88SV131 rev 1 (ARM9E-S V5TE core)
cpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled
cpu0: 16KB/32B 4-way L1 Instruction cache
cpu0: 16KB/32B 4-way write-back-locking-C L1 Data cache
mvsoc0 at mainbus0: Marvell 88F6282 Rev. A1 Kirkwood
mvsoc0: CPU Clock 1600.000 MHz SysClock 533.333 MHz TClock 200.000 MHz
mvsoctmr0 at mvsoc0 unit 0 offset 0x20300-0x203ff: Marvell SoC Timer
mvsocgpp0 at mvsoc0 unit 0 offset 0x10100-0x101ff irq 35: Marvell SoC General Purpose I/O Port Interface
mvsocgpp0: 50 gpio pins
mvsocgpp0: interrupts 96..103, intr 35
mvsocgpp0: interrupts 104..111, intr 36
mvsocgpp0: interrupts 112..119, intr 37
mvsocgpp0: interrupts 120..127, intr 38
mvsocgpp0: interrupts 128..135, intr 39
mvsocgpp0: interrupts 136..143, intr 40
mvsocgpp0: interrupts 144..151, intr 41
mvsocgpp0: Data Out: 0x75c00040
mvsocgpp0: Data Out Enable Control: 0x00002000
mvsocgpp0: Data Blink Enable: 0x00000000
mvsocgpp0: Data In Polarity: 0x00002000
mvsocgpp0: Data In: 0xf5c00000
mvsocgpp0: Interrupt Cause: 0x00000000
mvsocgpp0: Interrupt Mask: 0x00000000
mvsocgpp0: Interrupt Level Mask: 0x00000000
mvsocgpp0: High Data Out: 0x00010188
mvsocgpp0: High Data Out Enable Ctrl: 0x0002fc00
mvsocgpp0: High Blink Enable: 0x00000060
mvsocgpp0: High Data In Polarity: 0x0000a400
mvsocgpp0: High Data In: 0x000101e8
mvsocgpp0: High Interrupt Cause: 0x00000060
mvsocgpp0: High Interrupt Mask: 0x00000000
mvsocgpp0: High Interrupt Level Mask: 0x00000000
gpio0 at mvsocgpp0: 50 pins
mvsocrtc at mvsoc0 unit 0 not configured
mvsocts at mvsoc0 unit 0 not configured
com0 at mvsoc0 unit 0 offset 0x12000-0x1201f irq 33: ns16550a, working fifo
com0: console
com1 at mvsoc0 unit 1 offset 0x12100-0x1211f irq 34: ns16550a, working fifo
ehci0 at mvsoc0 unit 0 offset 0x50000-0x51fff irq 19: Marvell USB 2.0 Interface
usb0 at ehci0: USB revision 2.0
gtidmac0 at mvsoc0 unit 0 offset 0x60000-0x60fff: Marvell IDMA Controller/XOR Engine
gtidmac0: XOR Engine 4 channels, intr 5...8
gttwsi0 at mvsoc0 unit 0 offset 0x11000-0x110ff irq 29: Marvell TWSI controller
iic0 at gttwsi0: I2C bus
rs5c372rtc0 at iic0 addr 0x32: RICOH RS5C372[AB] Real-time Clock
gttwsi1 at mvsoc0 unit 1 offset 0x11100-0x111ff irq 32: Marvell TWSI controller
iic1 at gttwsi1: I2C bus
mvcesa0 at mvsoc0 unit 0 offset 0x30000-0x3ffff irq 22: Marvell Cryptographic Engines and Security Accelerator
mvgbec0 at mvsoc0 unit 0 offset 0x70000-0x73fff: Marvell Gigabit Ethernet Controller
mvgbe0 at mvgbec0 port 0 irq 11
mvgbe0: Ethernet address 2c:b0:5d:bf:18:da
makphy0 at mvgbe0 phy 0: Marvell 88E1116R Gigabit PHY, rev. 0
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
mvgbec at mvsoc0 unit 1 not configured
mvpex0 at mvsoc0 unit 0 offset 0x40000-0x41fff irq 9: Marvell PCI Express Interface
mvpex0: can't read pcicfg space
pci0 at mvpex0
Marvell 88F6282 SoC Kirkwood (miscellaneous memory, revision 0x01) at pci0 dev 0 function 0 not configured
mvpex0: can't read pcicfg space
mvpex1 at mvsoc0 unit 1 offset 0x44000-0x45fff irq 10: Marvell PCI Express Interface
pci1 at mvpex1
Marvell 88F6282 SoC Kirkwood (miscellaneous memory, revision 0x01) at pci1 dev 0 function 0 not configured
mvsata0 at mvsoc0 unit 0 offset 0x80000-0x87fff irq 21: Marvell Serial-ATA Host Controller (SATAHC)
mvsata0: GenIIe, 1hc, 2port/hc
atabus0 at mvsata0 channel 0
atabus1 at mvsata0 channel 1
mvsdio at mvsoc0 unit 0 not configured
uhub0 at usb0: Marvell EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
mvsata0 port 0: device present, speed: 3.0Gb/s
mvsata0 port 1: device present, speed: 3.0Gb/s
wd0 at atabus0 drive 0
wd0: <ST4000DM000-1F2168>
wd0: 3726 GB, 7752021 cyl, 16 head, 63 sec, 512 bytes/sect x 7814037168 sectors
wd1 at atabus1 drive 0
wd1: <ST4000DM000-1F2168>
wd1: 3726 GB, 7752021 cyl, 16 head, 63 sec, 512 bytes/sect x 7814037168 sectors
wd0c: DMA error reading fsbn 6 (wd0 bn 6; cn 0 tn 0 sn 6), retrying
wd0c: device timeout reading fsbn 6 (wd0 bn 6; cn 0 tn 0 sn 6), retrying
mvsata0:0:0: device disconnect
mvsata0:0:0: EDMA self disable happen 0x88
mvsata0:0:0: unable to stop EDMA
panic: EDMA enabled
Stopped in pid 0.5 (system) at netbsd:cpu_Debugger+0x4: bx r14
db>
